تالار گفتگوی تخصصی مهندسی و بازرسی جوش
What Does A Brake Master Cylinder Actually Do? - نسخه قابل چاپ

+- تالار گفتگوی تخصصی مهندسی و بازرسی جوش (https://www.weldeng.net/MyBB)
+-- انجمن: موضوعات عمومی (/Forum-%D9%85%D9%88%D8%B6%D9%88%D8%B9%D8%A7%D8%AA-%D8%B9%D9%85%D9%88%D9%85%DB%8C)
+--- انجمن: نظر، پیشنهاد و انتقاد در مورد انجمن ها (/Forum-%D9%86%D8%B8%D8%B1%D8%8C-%D9%BE%DB%8C%D8%B4%D9%86%D9%87%D8%A7%D8%AF-%D9%88-%D8%A7%D9%86%D8%AA%D9%82%D8%A7%D8%AF-%D8%AF%D8%B1-%D9%85%D9%88%D8%B1%D8%AF-%D8%A7%D9%86%D8%AC%D9%85%D9%86-%D9%87%D8%A7)
+--- موضوع: What Does A Brake Master Cylinder Actually Do? (/Thread-What-Does-A-Brake-Master-Cylinder-Actually-Do)



What Does A Brake Master Cylinder Actually Do? - henryicd - ۱۴۰۰/۷/۲۷ ۰۴:۵۴ صبح

What Does A Brake Master Cylinder Actually Do?

We should probably start by saying a دیدن لینک ها برای شما امکان پذیر نیست. لطفا ثبت نام کنید یا وارد حساب خود شوید تا بتوانید لینک ها را ببینید.
technically is not essential. You could use cable-actuated brakes, if you liked, like the cheap items you get on entry-level mountain bikes. On the other hand, to stand the strain of stopping one or two tonnes of metal, plastic and humans over 10-20 years, the cable would have to be massive.

There are more practical solutions, chief among which are hydraulics. The fact that liquid does not compress makes it perfect for transferring force from one part of a system to another. When it comes to the brakes in your car, the master cylinder is the key component in making that happen.

Picture a brake pedal in your mind. Delve into the relative darkness of that imaginary footwell and push that pedal with your mind foot. In most cars the pedal motion directly pushes a rod (known, funnily enough, as a pushrod) into one end of a sealed دیدن لینک ها برای شما امکان پذیر نیست. لطفا ثبت نام کنید یا وارد حساب خود شوید تا بتوانید لینک ها را ببینید.
filled with fluid, two pistons to displace the fluid, and springs to push back against the main force and return the brake pedal to its resting position when released.

Importantly, there are two exits from this tube. One leads to two diagonally-opposed wheels, while the other leads to the others. The two-line layout is a safety feature that ensures that even if a line should leak, you can still stop – albeit more slowly, with one wheel on each side and each end doing the job.

Let’s assume normal operation. Pressing the brake pedal pushes the two pistons, each sprung separately in a linear piston-spring-piston-spring layout, into the fluid, pushing the liquid down the lines into what are called slave cylinders; usually situated on brake calipers themselves. The slave cylinders then push the friction material onto the rotor.

Above the دیدن لینک ها برای شما امکان پذیر نیست. لطفا ثبت نام کنید یا وارد حساب خود شوید تا بتوانید لینک ها را ببینید.
, which is normally horizontal, is a vertical fluid reservoir. Its job is to make sure no (compressible) air gets into the system by retaining enough spare fluid volume to keep the system fully fed at all times and in all phases of its operation.

When the pedal is pressed, the piston in the دیدن لینک ها برای شما امکان پذیر نیست. لطفا ثبت نام کنید یا وارد حساب خود شوید تا بتوانید لینک ها را ببینید.
is pushed in forcing hydraulic fluid from the master cylinder through the tube and hose to the slave cylinder (on the left). The fluid pushes the slave cylinder piston toward the open end of the cylinder pushing the pushrod that connects to the lever on the clutch-operating shaft that in turn releases the clutch.

Manual transmissions are far from dead on the street, but late-model, overdrive six-speeds often demand a late-model hydraulic clutch release system as opposed to a mechanical system. This story will look at some of the basics for hydraulic clutch actuation. The system—similar to a car's hydraulic braking system—uses a hydraulic master cylinder to create line pressure plumbed (usually) to an internal دیدن لینک ها برای شما امکان پذیر نیست. لطفا ثبت نام کنید یا وارد حساب خود شوید تا بتوانید لینک ها را ببینید.
positioned on the transmission's input shaft.

Why would you want to convert to a hydraulic clutch assembly? Mechanical clutch systems can be a troublesome conversion in non-stock engine swap applications like slipping an LS engine into a Chevelle, Camaro, or early Nova. LS engines were never fitted with a provision for a mechanical Z-bar linkage mount so a bracket must be fitted or fabricated and the linkage modified to compensate for the difference created by the LS engine's repositioned flywheel mounting surface. Other headaches that hydraulic actuation solves include header clearance issues and a reduction in pedal effort, making the driving experience more pleasant.

What Is A Brake Hose?

A دیدن لینک ها برای شما امکان پذیر نیست. لطفا ثبت نام کنید یا وارد حساب خود شوید تا بتوانید لینک ها را ببینید.
is a vital brake component responsible for delivering brake fluid from your vehicle’s master cylinder to the wheel cylinder (in drum brakes) or brake caliper (in disc brakes).

But wait.

Brake fluid is delivered through brake lines, right?

Yes.

So, does that mean a brake line and a brake hose are the same?

Not exactly.

They’re similar in that both the brake line and the brake hose act as conduits to transport brake fluid from the master cylinder.

However, they’re designed for different use cases.